Dacor burner keeps clicking? What to Check Before You Book Repair

A Dacor burner that keeps clicking usually has moisture, residue, or a knob left in the light position keeping the igniter sparking. Check that the knob has been turned to a cooking setting and that the area around the igniter is dry. If clicking continues with every knob off, or you smell gas, stop and book.

A Dacor burner that keeps clicking after it lights is usually a wet or grounded igniter that still thinks there is no flame. Continuous spark with the knobs off is a different, more urgent module fault.

Why does a Dacor burner keep clicking?

Spark should stop once the flame is established. If it does not, the igniter is seeing moisture, a cracked insulator, or a switch that never opened. Rangetops share spark modules — one wet burner can click the whole row.

Safe checks you can do first

1. Turn all knobs to off. If clicking continues, treat it as a module/switch fault and cut power at the breaker if it is safe to reach.
2. If it only clicks on one burner, dry that igniter and cap.
3. Look for a cracked ceramic insulator around the spark tip.
4. After a deep clean, make sure the spark tip is not buried in polish or standing water.

Do not keep cooking over a burner that sparks into your hand or into a pan handle.

How electronic ignition works on Dacor gas burners

The use-and-care manual for the Modernist gas cooktop describes the ignition this way: pushing in and turning the knob to Lite gives a click-click-click sound that shows the ignition system is working. The sparking is meant to last until the burner lights, and the manual for the Modernist Pro range puts that at about 4 seconds, with sparking stopping once the burner ignites.

The same cooktop manual lists a clicking burner during operation with a simple cause: the knob was left in the Lite position. It says to turn the knob to the desired setting after ignition, and to contact a technician if clicking persists. That is the first owner check, and it needs no tools.

The Pro range manual adds that the igniter also sparks if a draft or home ventilation affects the flame. It advises eliminating drafts and lowering the ventilation blower speed. A hood running at full speed can therefore make a healthy burner click.

Likely diagnostic areas

• Moisture around the igniter after cleaning or a boil-over.
• A cracked igniter insulator.
• A stuck spark switch on a valve stem.
• A spark module that never stops pulsing.
• Parts left misseated after cleaning, such as a cap or burner base.

None of those is confirmed by the symptom alone. Wiring, connectors, restrictions, and the control can produce the same kitchen experience as a failed part.

Wet igniters, caps, and cleaning habits

The cooktop manual says the white ceramic electrodes must be clean and dry. It says not to clean igniters with water and not to spray cleaner into the manifold holes. Burner caps and heads can be washed, but they must be dried completely, and parts that are installed incorrectly cause poor ignition or uneven flames.

That is the practical link to clicking after a cleaning session. Water or cleaner left around the electrode can keep the igniter sparking, and a cap that is off its seat can change how the flame forms. Seat each cap and check that the burner base is aligned before you try again.

Flame color is another clue. The Pro range manual describes a normal flame as steady and blue, notes that an orange tint can appear from foreign matter in new gas lines and may fade with use, and says yellow tips are normal on LP gas. Large or yellow flames can also indicate the wrong burner orifice for the type of gas, so a flame that looks wrong is a service question, not a cleaning one.

When should you book Dacor repair in Los Angeles?

Book cooktop repair if clicking continues with knobs off, if spark continues after the area is dry, or if you smell gas while it clicks. Do not dismantle gas valves. Book as well if the clicking only stops when the hood blower is slowed and returns whenever it speeds up, since the cause may sit with the burner and not the airflow.

Common questions

Why does my burner keep clicking after it lights?

One documented cause is a knob left in Lite, so turn it to the desired setting after ignition. If it still clicks, moisture around the electrode or a misseated cap are the next things to look at.

Is it normal for the igniter to click?

Yes, at the start. The manual for one Dacor range says the igniter sparks until the burner lights, about 4 seconds, and sparking stops once it ignites.

Can a range hood make my burners click?

The Pro range manual says drafts or home ventilation can cause sparking and advises lowering the blower speed. If clicking stops when the hood is slowed down, airflow is the cause.